Fibron Heat Transfer Material
Fibron Heat Transfer Material
Fibron Heat Transfer Material for Plotters
• 4 Mil matte polyurethane with clear mylar liner, designed for use with plotters. 45° angle blade recommended
• With mirrored image, heat transfer graphic with heat press onto garment using firm pressure at 330-335° F for 17-20 seconds for most colors. Peel warm
• Works with cotton, polyester, spandex, lycra, and some athletic mesh fabrics. WILL NOT adhere to nylon
• See Installation bulletin for more information
• To ensure greatest durability, garments should be washed inside out on gentle cycle
• If applying to 100% cotton, we recommend washing the material first to remove excess lint and fuzz.
• Deco Sparkle patterns will not layer. They should be applied at 300°F for 10-12 seconds. Peel Cool. Cool wash, tumble dry low heat.
• Cobra, apply 330°F for 12-15 seconds, peel cool
• Fibron can be layered, except the Neons, Deco, and Metal Flake.
Polyurethane Garment Film
Product Description
A Matte polyurethane material designed to be used with vinyl plotters for cutting graphics for garments.
Fibron is thermal transferred with heat by a heat press on to cotton, blended fabrics, polyester fabrics, spandex and other fabrics. 100% cotton needs to be prewashed for best success. Will not adhere to nylon, dazzle cloth, shiny polyester or moisture wicking materials.
Note: Ironing on is not recommended.
Product Construction
• Film: Polyurethane
• Finish: Matte
• Thickness: 4 Mil
• Liner: Clear Mylar Carrier
• Durability: Life of the Garment
Application Recommendations
• Can be die cut and weeded with plotters.
• Note: Always Mirror Image or Reverse Cut
• Position weeded graphic on garment.
• Heat transfer graphic with heat press on to garment using FIRM HARD PRESSURE at 345-350°F for 20 seconds.
• Deco Sparkle materials should be applied with 300°F for 10-12 seconds, Peel cold. Deco Sparkle patterns will not layer.
• Cobra, apply 330°F for 12-15 seconds, peel cool
• Fibron can be layered, except the Neons, Deco, and Metal Flake.
• Remove Clear Mylar Carrier from garment.
• Be advised that dye migration has occurred with low energy dyes in polyester and poly-blend fabrics
• It is recommended to reheat prints 10 seconds after removing the application tape for greater durability. Place a PTFE sheet or release liner over graphic before applying heating
* To insure greatest durability, decorated garments should always be turned inside out and washed in gentle cycle, cold water and tumble dry. Avoid use of bleach or detergents containing bleach.
Fibron Heat Transfer Material for Plotters
• 4 Mil matte polyurethane with clear mylar liner, designed for use with plotters. 45° angle blade recommended
• With mirrored image, heat transfer graphic with heat press onto garment using firm pressure at 330-335° F for 17-20 seconds for most colors. Peel warm
• Works with cotton, polyester, spandex, lycra, and some athletic mesh fabrics. WILL NOT adhere to nylon
• See Installation bulletin for more information
• To ensure greatest durability, garments should be washed inside out on gentle cycle
• If applying to 100% cotton, we recommend washing the material first to remove excess lint and fuzz.
• Deco Sparkle patterns will not layer. They should be applied at 300°F for 10-12 seconds. Peel Cool. Cool wash, tumble dry low heat.
• Cobra, apply 330°F for 12-15 seconds, peel cool
• Fibron can be layered, except the Neons, Deco, and Metal Flake.
Polyurethane Garment Film
Product Description
A Matte polyurethane material designed to be used with vinyl plotters for cutting graphics for garments.
Fibron is thermal transferred with heat by a heat press on to cotton, blended fabrics, polyester fabrics, spandex and other fabrics. 100% cotton needs to be prewashed for best success. Will not adhere to nylon, dazzle cloth, shiny polyester or moisture wicking materials.
Note: Ironing on is not recommended.
Product Construction
• Film: Polyurethane
• Finish: Matte
• Thickness: 4 Mil
• Liner: Clear Mylar Carrier
• Durability: Life of the Garment
Application Recommendations
• Can be die cut and weeded with plotters.
• Note: Always Mirror Image or Reverse Cut
• Position weeded graphic on garment.
• Heat transfer graphic with heat press on to garment using FIRM HARD PRESSURE at 345-350°F for 20 seconds.
• Deco Sparkle materials should be applied with 300°F for 10-12 seconds, Peel cold. Deco Sparkle patterns will not layer.
• Cobra, apply 330°F for 12-15 seconds, peel cool
• Fibron can be layered, except the Neons, Deco, and Metal Flake.
• Remove Clear Mylar Carrier from garment.
• Be advised that dye migration has occurred with low energy dyes in polyester and poly-blend fabrics
• It is recommended to reheat prints 10 seconds after removing the application tape for greater durability. Place a PTFE sheet or release liner over graphic before applying heating
* To insure greatest durability, decorated garments should always be turned inside out and washed in gentle cycle, cold water and tumble dry. Avoid use of bleach or detergents containing bleach.
